Concrete Mixes by Weight and Volume

A Table for Concrete Mixes by Weight in Kilograms,

by Bag, and by Cubic Meter, for Various Strengths

A batch of concrete mixed on site, moved by wheelbarrow, to the foundation floor.
A batch of concrete mixed on site and and moved by wheelbarrow and placed on the foundation floor area.

We have had numerous requests for concrete mix ratios by weight, by volume, and by mass. Here is a table that was released by the Cement and Concrete Institute for trial concrete mixes from 10MPa to 40MPa. These are trial mixes and should be used to test your concrete before it is used in any construction work. Your “competent person” or project manager should always assess and approve any concrete work undertaken on your site.

The mix proportions in the table are by mass and volume, using different size stone, for different strengths of concrete. You must add water to the mixture until it becomes workable; you can judge this by eye. The difference between various cements and aggregates is not taken into account with these mixes. Make sure that the water is kept together with the mix and is not allowed to drain/run away as this could result in a weaker mix.

NOTE:

These proportions are based on the assumption that a CEM type cement of strength class 32,5 will be used. Cement of strength class 42,5 or higher will give a stronger concrete but may be less economical. Cements with high extender contents (eg CEM 11/B or CEM 11) will develop strength more slowly and will require particular care with curing. Masonry cements complying with SABS ENV 413-1 should only be used with specialist advice.

The amount of water required is not given in the table. The mix should contain enough water to achieve the required consistence. Consistence may be assessed by eye or measured by carrying out a slump test (SABS Method 862-1: 1994)

A mix made according to this table, and to the required consistence, should be assessed for workability and stone content before being used on a large scale.

Quantities of materials per cubic metre of concrete are net. Allow for wastage when ordering – for instance 3% on cement and 10% on aggregates.

A standard bag of cement weighs 50kg so the equivalent quantities and weights are:

1 Bag cement = 50kg = 0.2 m(cubic metre)

ConcreteMixTableX580

Below is the nominal mix proportions (also referred to as the ratios of mixes) for different strength categories, using a 19mm stone.

Concrete Mix Ratios

NB. Low would be average 15MPa, medium 25MPa and high 35MPa. This is a guide only and quantities must be adjusted for the final requirements and specified by a “competent person“.

About Janek

Check Also

What Is the SABS?

What Is the SABS? What Does the SABS Do? The South African Bureau of Standards …

21 comments

  1. Asuquo Asuquo

    Thank you,but how can i reduce the amount of the materials so that it can enter or contain in a 56 litres mixer.

  2. You have to work in batches Asuquo

  3. Greetings, I want to do 75 s/m concrete floor, @100mm thick, how much cement, sand and stone will I need for this job. Regards

  4. Hi Roger, You will need 75sq m X .1 = 7.5 cubic meters of concrete. The tables on this page “concrete-mixes-by-weight” will give you the amounts that you will need.

  5. deepak kumar

    pls tell me the process of estimating of the building and roads

  6. Sorry I can’t help!

  7. kifle tefera

    thank u for yrs. help

  8. Good day to you

    I am throwing a slab with a required strength of 25 MPA. The area is 16m² at a required thickness of 75mm, which calculates to 1.2 m³ of concrete.

    The above tables only gives me the ratio mix for 1m³, and I am required to have slightly more.

    How much more cement, sand & stone will I require to complete the job satisfactorily? I will be using the 19mm stone. Would it be safe to use say 9 bags of cement to 1m³ sand and 1m³ of stone?

    I will be grateful if you could assist me with this calculation.

    Many thanks for the helpful website.

    Regards.

  9. Hi Laurence, Ideally to get your 1.2³ m the number of bags will be .841³m with .84³m each sand and stone in theory. It is best to always mix a little extra as there will always be shrinkage and some waste. So your ratio of 9 bags to 1³m sand and 1³m stone will fine be for the strength and quantity you need.

  10. Good morning Janek

    Many thanks for your help and advice. It is really appreciated. I’ll give it a bash and see how we do. This is a very helpful website. Thanks again.

    Kind regards.

  11. Flip Opperman

    What strength of concrete do I need to threw for a slab to be used as parking for motor vehicles, small truck up to 4 tons and forklifts with a capacity of 5 tons. Slab will also be used as a loading bay.

  12. what is the correct ratio mix 25mpa 1 shovel cement how many shovels premix do i need

  13. We have a very inexpensive handbook that will give you all the info you need about concrete and mortar.

  14. how to calculated the weight
    of water

  15. What does Mpa stand for

  16. How can site concrete mix design be made more reliable, even against readymix concrete from batching plant?

  17. Hi Menas, The only way on site is to make a batch box and monitor the people doing the mixing closely. The other factor that come into the calculation is the stone size and the dampness of the sand. So the mixing becomes an imprecise science. If you are worried it might be better to use a ready mix where you have some recourse if anything should fail.

    http://sans10400.co.za/wp-content/uploads/2016/08/BatchingBox-Size.gif

  18. Hi Hari, 1cc of water = 1 gram so 1 Liter will = 1 Kg = cu vol 100mmx100mmx100mm = 1000cc. Find out what the volume is first then you will have the weight.

  19. Hi Ben, It is the Ultimate tensile strength of the concrete, named after the French mathematitian Pascal (Pa) and the M = Mega hence MPa. You can read more here: https://en.wikipedia.org/wiki/Ultimate_tensile_strength

Leave a Reply

Your email address will not be published. Required fields are marked *